Wi-Fi help at home: when the internet drops

Wi-Fi not reaching the bedroom, or the internet gone again? Call us. We come to you from Rodewisch, find where the problem is and set up your router and Wi-Fi to suit your home.

Request Wi-Fi help

You do not need to know what the cause is.

The film stops halfway through. The phone has no signal in the bedroom. Or the TV has been insisting since yesterday that there is no Wi-Fi at all. Tell us what you were trying to do and what happened instead. That is enough.

Almost always it is one of three places: the device, the router (is it in a cupboard, perhaps?) or the line that brings the internet into the house. We find out which, and bring the Wi-Fi to the places where you need it.

Only one device is causing trouble.

The phone works in the same spot but the laptop does not? Then we leave the router alone and look at the laptop. We set up its Wi-Fi connection again and bring the network software up to date. Then you try it out where you normally use it.

It works in the living room, not in the bedroom.

Then the signal is too weak by the time it gets there. There are walls in between, sometimes a concrete ceiling. We walk through the rooms with you and measure at your spots. Sometimes moving the router is enough. Sometimes a second Wi-Fi point in the hallway is needed.

Everything is gone at once.

TV, phone and computer all offline at once? Then it is the router or the line. We check the router to see whether your provider’s signal is arriving at all. If it is, we set the router up properly again. If nothing arrives, you will know afterwards what to report to your provider.

Three comparisons, then we know.

The route to the internet has only a few stages: your device, wirelessly to the router, then from the router over your line to the outside world. We do not guess where it is stuck. We compare.

First: another device in the same place. If the phone works where the laptop is struggling, the laptop is the problem. Second: the same device in another room. If the laptop works perfectly next to the router, the signal simply does not reach the back. Third: a device connected by network cable straight to the router (we bring the cable). If it is slow on the cable too, the Wi-Fi is not to blame. Then too little is reaching the house in the first place.

After that it is clear where to start. And you have not bought a repeater on a hunch.

THE WAY TO THE INTERNETYOUR DEVICEROUTERLINEINTERNETTHREE COMPARISONS NARROW IT DOWNOTHER DEVICE,SAME PLACESAME DEVICE,OTHER ROOMBY CABLE STRAIGHT TO THEROUTERTHE WAY TO THE INTERNETYOUR DEVICEROUTERLINEINTERNETTHREE COMPARISONS NARROW IT DOWNOTHER DEVICE, SAMEPLACESAME DEVICE, OTHERROOMBY CABLE STRAIGHT TO THEROUTER
FIG. 1 · NARROWING DOWN WI-FI AND INTERNET PROBLEMSDASHED = WIRELESS · GOLD = HANDOVER TO THE INTERNET

Before you pull the plug: a look at the router.

You do not have to do this. But if you are standing in front of it anyway: look at the lights. Are they the way they always are? Is one flashing that is normally steady, or is one red? A photo with your phone is enough. From that we can often tell by phone whether the internet reaches the router at all.

After that you are welcome to restart the router: pull the plug, wait two minutes, plug it back in. That deletes nothing. (If your telephone is connected to the router, it will not work in the meantime.) If everything works again afterwards, all is well. If the fault comes back after a few days, call us, because then it has a cause that a restart only covers up.

The small reset button on the back is a different matter entirely. It returns the router to its factory state, and then the login details, Wi-Fi name and phone numbers are gone. Please leave that one to us. If a router really has to be reset, we first back up its settings (most routers allow this) and then set it up completely again afterwards.

Is your router in a cupboard?

That is where it stands in many homes: in the hallway cupboard, behind the TV, down in the cellar where the line comes into the house. It looks tidy. For the wireless signal it is the worst place, because every cupboard door and every wall in between swallows signal.

We put it out in the open and as high as possible, ideally where it reaches your important rooms without a detour. If the cable to the socket is too short, we use a longer one. Then we go to your spots with you and see what has changed. Often that settles it, without buying a new device.

Wi-Fi in the back room: two ways.

If the router cannot manage on its own, there are two ways. Which one suits you comes down to a single question: is there a network cable running to that room?

Wirelessly: a repeater picks up the router’s Wi-Fi and passes it on. That only works if it still has good reception itself. So it belongs halfway between the two, not in the room where nothing arrives any more (yet that is usually exactly where it ends up). We find the right place for it and register it with the router. In larger homes and across several floors we set up mesh. That means several Wi-Fi points working together and handing your phone on by themselves as you walk through the house.

By cable: if there is already a network cable to the back room or the upper floor, we connect a second Wi-Fi point there (the technical term is access point). That is the more stable solution. The signal travels through the cable up to that point and loses nothing on the way.

If you need a device for this that is not there yet, we tell you beforehand which one and what it costs. If you would like to try it yourself first, the guide “Improving your Wi-Fi at home” explains what you can do without us.

WIRELESSROUTERREPEATERBACK ROOMBY CABLEROUTERWI-FI ACCESS POINTBACK ROOMWIRELESSROUTERREPEATERBACK ROOMBY CABLEROUTERWI-FI ACCESS POINTBACK ROOM
FIG. 2 · TWO WAYS TO THE BACK ROOMDASHED = WIRELESS · GOLD = RECEPTION MUST STILL BE GOOD HERE

2.4 or 5 GHz? We set that up for you.

Your router transmits on two bands at once, newer ones on three. Think of them as roads. 2.4 GHz is the country road: slower, but it goes far and gets through walls well. 5 GHz is the motorway: fast, but after a few walls it ends. 6 GHz is faster still and shorter still, and only very new devices can use it.

In practice: the TV and the laptop near the router go on 5 GHz, so the film does not stutter. The smart socket, the older printer and everything far away at the back run on 2.4 GHz. Many of these devices cannot do anything else anyway.

Usually the router manages this itself, under a single Wi-Fi name. If that does not work for one device (the classic case: the new socket simply will not register), we set it by hand. You do not have to remember the numbers.

Getting TVs, printers and phones onto the Wi-Fi.

A new TV, a printer, the new tablet: every device has to be registered on the Wi-Fi once. We do that for you, on the right network and with the right password. Anything that stays in one place and has a network socket (the TV, for example), we prefer to connect by cable if the router is nearby. Then nothing stutters, and the Wi-Fi stays free for everything else.

We are only done when the device does what it should. The streaming app plays, and a page comes out of the printer.

This page is about the connection. For setting up the app for a smart lamp, a printer that says “offline”, or getting the picture from your phone onto the TV, see Printer, TV, phone & smart home.

A separate Wi-Fi for your visitors.

The grandchildren want to get on the Wi-Fi, and so does the neighbour. You do not have to give out your own password for that. We set up a guest Wi-Fi with its own name and its own password (most routers have this built in). Anyone using it can get online, but cannot reach your computer or your photos.

That is also why your visitors cannot print on your printer from the guest Wi-Fi. That is deliberate.

While we are at it, we sort out the passwords. One is for the Wi-Fi, the other for the router’s settings, and the two are easily mixed up. We show you where both are written and how to change the guest password yourself.

And if it is the provider?

Then we will tell you. But only once we know. For that we connect a laptop by cable straight to the router. If the internet is slow or gone there too, your Wi-Fi is ruled out as the cause.

Next we read the router’s log. It keeps a record: when the line dropped, how often, and how much speed arrives. We write that down for you, with times and what the router noted. With that you can call your provider and say exactly what is going on.

You do not need a new router in that case. You can save the money.

If you consistently get less than your contract promises, there is an official way to measure it: the broadband measurement by the Bundesnetzagentur. We show you how the measurement works. And if you are thinking about a different connection anyway, our guide to the internet in the Vogtland shows which DSL, fibre and wireless options are really available here.

How it works.

  1. You call.

    Tell us what does not work and in which room. You do not need to prepare anything; leave everything as it is (the reset button too, please). While still on the phone, you will hear what we suspect and roughly what it will cost. That conversation costs nothing.

  2. We come to you or connect remotely.

    If it is about reception in your rooms, we come to you. That can only be measured on site. We can often change a router setting remotely, as long as one computer can still get online. Then there is no travel charge.

  3. You try it out yourself.

    At the end you go to your spots with your phone or tablet and test. We explain what we changed and show you where the Wi-Fi name and password are written. If anything still needs sorting out with your provider, you will know exactly what.

We are from Rodewisch and visit you at home in the Vogtland, by appointment. If the computer itself is also giving trouble, you will find everything else under PC help. The page on remote support explains how we connect remotely.

You know what it costs beforehand.

We charge by time, in quarter-hours. If we come to you, travel is added; with remote support it is not. Before we start, you will hear by phone roughly what it will come to. And if a repeater or a second Wi-Fi point is needed, you know its price beforehand too.

The exact rates are in the overview below and in the full price list. You can reach us Mon–Fri 8:00–17:00 on +49 3744 4399760.

Specification

We help when
the Wi-Fi does not reach far, the internet drops or a device cannot find the network
What we set up
Router, repeater, mesh and a guest Wi-Fi
Devices on the Wi-Fi
TV, printer, phone, tablet, smart devices
At your home
Home visit in the Vogtland by appointment
Remotely
By remote support, as long as one computer can still get online
Initial assessment
Free, by phone
Price
By phone, before we start

Prices

€69 per hour incl. VAT (MwSt.), charged per quarter of an hour or part thereof. Travel from €20 incl. VAT. The initial assessment by phone is free.

Questions & answers

Common questions, answered briefly.

Why does my phone show full Wi-Fi, but no page loads?

The bars only show how well your phone reaches the router. They do not show whether the router itself is online. If it is not, the cause is the router or the line (or a repeater that can barely pick up the router any more). We can see which at the router.

I already have a repeater and it is still slow. Why?

It is probably in a dead spot. A repeater can only pass on what reaches it; if it is placed where the Wi-Fi is already weak, it spreads a weak signal. It belongs halfway between the router and the room where you need Wi-Fi. We will find the place with you and measure again afterwards.

Do I need a new router or a mesh system?

Often not. First we get the most out of what you already have. A router that moves from the cupboard to a shelf sometimes does more than a new device. If that is not enough for your home, we will tell you what is worthwhile and what it costs. Mesh simply means several Wi-Fi points working together, so that your phone switches to the nearest one by itself as you walk through the house.

Can you set up my new router?

Yes. We connect it, enter your provider’s login details and set up Wi-Fi and telephone. If you like, the Wi-Fi keeps the same name and password as before. Then your TV, printer and phones find their way back by themselves, and you do not have to type anything in again. (With some providers, your own router first has to be activated; we get that started with you.) It is best to call before you buy one: we will tell you which one suits your line.

Should I reset the router to factory settings?

Please do not. Afterwards the login details, Wi-Fi name and phone numbers are gone, and the fault is often the same. You can unplug the router and plug it back in after two minutes at any time; that deletes nothing.

Do I need to worry about 2.4 and 5 GHz?

No. We set that up, and afterwards your devices choose by themselves. In case you are curious: 2.4 GHz reaches further, 5 GHz is faster.

Do you also connect TVs and printers to the Wi-Fi?

Yes, and we are only done when the programme is playing and the test page is in the printer tray. We also connect phones, tablets and smart devices such as sockets or lamps. For help using them, setting up their apps or scanning, see our “Printer, TV, phone & smart home” page.

Can this be done remotely?

Some of it. As long as one computer can still get online, we can connect to it and set up the router from there. If the internet is gone completely or the problem is reception in particular rooms, we come to you.

What does Wi-Fi help cost?

€69 incl. VAT (MwSt.) per hour, charged for each quarter-hour or part thereof. Travel charge from €20 incl. VAT. The initial assessment by phone is free. There is no travel charge for remote support. Before we start, we tell you by phone what we suspect and roughly what it will cost. If an extra device is needed, such as a repeater, we also tell you its price beforehand.

Will the Wi-Fi reach every room afterwards?

That is what we work towards. You show us the places where it should work (armchair, desk, bed), and we measure there before we leave. There is one limit: even the best Wi-Fi cannot distribute more speed than your line brings into the house. And if the fault is in your provider’s network, only they can fix it. We will then tell you exactly what to report to them.

Contact

Tell us where the problem is.

A sentence like “The Wi-Fi does not work in the bedroom” is enough. You will hear straight away on the phone what we suspect and roughly what it will cost.

+49 3744 4399760Mon–Fri 8:00–17:00
CallSend an enquiry

PARTS LIST · SHEET 1/1

What this page is made of

Values measured at build time. With JavaScript, your browser measures them again live.

ITEMPARTTYPESIZE
01index.htmlDocument≈ 29 kB
02styles.cssStylesheet≈ 20 kB
03scripts.jsScript≈ 13 kB
04archivo-variable.woff2Font≈ 58 kB
05ibm-plex-mono.woff2Font≈ 30 kB
06favicon.svgImage< 1 kB

Advertising or analytics cookies: none. Without your consent, the page loads nothing from third-party servers apart from Cloudflare, our delivery service. Fonts, scripts and images are hosted by us. That is how we build your IT, too.

OUTSIDE OFFICE HOURS

Feel free to call anyway

Our regular office hours are Monday to Friday, 8:00–17:00.

In the evening and at weekends the number is forwarded to us, and often someone will pick up. We cannot promise that, though.

If nobody answers, leave a short message on the voicemail: your name, your number and what it is about. We will call back as soon as we can, on the next working day at the latest.

The call costs nothing. If someone has to start work straight away outside office hours, the surcharge in the price list applies.

Call now+49 3744 4399760

Prefer to write? Use the contact form or e-mail [email protected]. We will read it on the next working day.

DIAGNOSIS · AT-K2

What do you need help with?

↵ SELECTESC CLOSECALL: +49 3744 4399760

Custom settings

Which services may load?

Strictly necessary

The choice you make here and your settings for colour scheme and motion. These are kept as small entries on your device and are never sent to a server. They are needed for the site to work and therefore cannot be switched off.