Guide · AT-R17REV. 2026-A
Wi-Fi at home: range, dropouts and why a repeater is rarely the answer

By Benjamin ReichertNetworks, hardware, support · IT specialist for system integration (Fachinformatiker, IHK)Last updated:
Wireless signals do not behave like a cable. They get weaker the further they travel, and anything in between eats them up. If you understand what eats them up, you save yourself the money you would otherwise spend on the wrong device.
Measure first, then buy
Take your phone and walk through the home. On many Android devices the Wi-Fi settings show the signal strength in dBm; on an iPhone you need an app for that. Note the value in each room.
To put it in context: anything up to about −60 dBm is good, from −70 it gets sluggish, below −80 the connection keeps dropping. The minus sign matters — −50 is better than −80, even though the number looks smaller.
While you are at it, check whether both frequency bands actually arrive. Many routers broadcast two networks, often with something like “5G” in the name. That has nothing to do with mobile data.
And a second measuring point before you spend any money: measure once with your computer connected directly to the router by network cable. If too little arrives even there, Wi-Fi is not your problem but the connection itself — in that case the guide “Internet in the Vogtland” will help. You can measure both with our speed test, which also tells you straight away whether the value is enough for working from home and streaming.
The Wi-Fi planner estimates roughly how many mesh points or access points your flat or house needs, based on floor area, number of floors and wall material.
What weakens Wi-Fi signals
Not all walls are equal. A plasterboard wall costs almost nothing, a load-bearing brick wall noticeably more, and reinforced concrete is practically a wall of metal mesh. That is exactly why reception one floor down is often worse than two rooms away.
The usual suspects in the home: underfloor heating, large mirrors, aquariums, fridges and metal shelving. Water absorbs wireless signals particularly well, which is why the bathroom is so often a dead spot.
The router is almost always in the wrong place
It sits where the phone socket is. That means in the hallway, behind the door, in a cupboard or under the television. For wireless signals, these are the worst places a home has to offer.
A router transmits roughly in a sphere. If it stands in a corner, half the sphere goes outside to the neighbour. If it stands in a cupboard, the wood dampens it further. Placed in the open and as centrally as possible, it often brings more than any extra device, and costs nothing.
Repeater: what you pay for it
A simple repeater has one radio module. It has to receive and transmit with it, and doing both at the same time is not possible. It takes a packet, waits, passes it on. In the end about half the speed is left.
There is a second problem: the repeater can only pass on what reaches it. If you plug it in where reception is already poor, you spread poor reception. It belongs halfway along the route, not at the destination.
What works instead
A second access point on a cable. If you can somehow get a network cable to the distant room, the matter is settled. A second device hangs there, broadcasting the same network name, and your phone switches over automatically as you walk through.
It does not have to be a new device. The old router lying in a drawer since you changed provider can be set up as a second access point on most common models. Look there first before you buy anything.
Mesh, if no cable is possible. Several devices that coordinate with each other. Better than a repeater, because they hand over your device deliberately and often reserve a separate band for the link between themselves.
Powerline as a fallback. Network over the mains wiring. It can work well, it can disappoint. It depends on the wiring in your building, and you cannot say for sure beforehand.
If it is not the range
If the connection drops even right next to the router, the cause lies elsewhere. Often it is the radio channel: in a block of flats many networks overlap, and at its last start your router picked a busy channel.
Cutting the router’s power for two minutes is the rough method, because it makes a new choice at start-up. You can do it more precisely in its own interface: common models show there which channels the neighbours occupy and let you set your own to a fixed channel. Checking this is more useful than buying a new one.
If, on the other hand, everything drops at the same time, even on a cable, it is not the Wi-Fi but the line. Then only your provider can help. How to tell the two apart is explained further up: check against your phone on mobile data.
When you should call us
If you have already bought two devices and it still does not work. We survey the space instead of guessing, and we will also tell you if a device you already own is enough. What a visit costs is fixed beforehand; you will find the rates in the price list.
Different rules apply to businesses with a hall, warehouse or workshop. Why wireless signals drop out there and what a proper site survey does differently is covered in the guide “Wi-Fi that also works in the factory workshop”.
Common questions
Does a more expensive router give better range?
Usually not as much as the price suggests. Transmit power is capped by law, and the expensive device sticks to that limit too. What better routers can do is serve more devices at once and switch between the frequency bands more cleverly. That does not help against a reinforced concrete ceiling.
What is the difference between a repeater and mesh?
A repeater receives the signal and passes it on, using the same radio module for both, which is why the speed is halved. A mesh system consists of several units that coordinate with each other and hand your device over automatically to the nearest suitable point. Mesh works best when the points are connected by cable.
Can I run the cable through the power socket?
Powerline works, but it is temperamental. It depends on the wiring in your building: old cables, sub-meters or a different phase in the fuse box cut the speed sharply. In an older building a test is worthwhile; in a new build with cleanly separated circuits it is often disappointing. A proper network cable always beats Powerline.
Why is my Wi-Fi slower in the evening?
Because everyone is transmitting then. Wi-Fi, Bluetooth, baby monitors and microwaves share the 2.4 GHz band, and in a block of flats twenty networks can easily overlap. The 5 GHz band is much emptier, but it gets through walls less well.
Do I need to change my Wi-Fi password regularly?
No. A long password with current encryption is better than a short one that changes every three months. You should change it when someone knows it who should no longer know it: after a tradesman has visited, or if it has hung on the fridge for a long time.