Guide · AT-R15REV. 2026-A

Printer won’t print: ruling out the faults one by one

Offline, not found, blank pages: the cause is almost always mundane. What matters is the order in which you rule things out.

By Benjamin ReichertNetworks, hardware, support · IT specialist for system integration (Fachinformatiker, IHK)Last updated:

The printer has stood in the corner for half a year, now you need it for a form, and nothing happens. The job is stuck in the queue, the printer shows “offline”, or it is not found at all.

The annoying part: there are about ten mundane causes, and if you work through them in the wrong order, you can lose half an afternoon.

1 · AT THE DEVICECheck error display2 · WI-FImost common cause3 · AT THE COMPUTERClear the queue

First: two minutes at the device

Before you touch anything on the computer, look at the printer.

  • Is an error indicator lit or flashing? Flashing symbols on the device are almost always more important than any message on the screen.
  • Is there paper in it, and is it sitting correctly in the tray?
  • Is there a scrap of paper left inside? Open the back and the flaps and have a look.
  • Are all the cartridges inserted and recognised?
  • Is the printer set to the wrong paper source in its menu?

A surprisingly large share of cases is already solved at this point.

Then: how is the printer actually connected to the computer?

This is the key question, because everything else depends on it.

By USB cable. Then the fault can only be in the cable, the port or the driver. Try another USB port, preferably directly on the computer and not via a hub.

By Wi-Fi. By far the most common source of faults. More on that in a moment.

By network cable to the router. Rare in private homes, but the most stable option.

The most common causes with Wi-Fi printers

The printer has been assigned a new address

Your router assigns the addresses on the network automatically, and after a power cut or a router restart the printer may get a different one. The computer still looks for it under the old one. Result: printer offline, even though it is standing right next to you with its lights on.

The lasting solution is to have the router assign the printer a fixed address. That is a one-off effort and never a problem again afterwards.

Wrong wireless network

Modern routers broadcast on two frequency bands, 2.4 and 5 gigahertz, and newer ones also on 6 gigahertz. Many printers can only use 2.4. Such a device cannot see the faster networks at all, so it cannot get lost there.

It still becomes difficult if all the bands have the same name. Setup usually runs through an app on your phone, and if the phone happens to be on the 5 GHz band, it will not find the printer. On top of that, many routers push their devices into the faster band by themselves, which makes things even more unpredictable.

Remedy: for the setup, briefly switch off the 5 GHz network in the router. Or give the 2.4 GHz band a name of its own permanently, so that you can move your phone onto it deliberately.

A similar problem: the printer is on the guest network, or the phone is. Devices on the guest network cannot see the rest of the network. That is how it is meant to work.

Too far away

A printer in the cellar and the router on the first floor, with a concrete ceiling in between. The printer reports “connected” but keeps losing the connection. Check the signal strength in the printer menu; many devices show it.

The most common causes on the computer

The queue is stuck

One failed job blocks all the ones after it. The classic: you print five times because nothing happens, and when the problem is fixed, five pages come out.

Open the print queue and delete all jobs. If a job cannot be deleted, the Windows print service is stuck. Restarting the computer reliably clears it. If you are confident enough to go into the Windows services, restart the “Print Spooler” service instead. That saves the restart.

The wrong printer is selected

Besides your device, Windows sets up “Microsoft Print to PDF”, “Fax” and sometimes copies of the printer with a number added. If such a copy is the default, the job goes nowhere. Set the right device as the default and delete the surplus copies of your printer, that is, the entries with the added number. Leave “Microsoft Print to PDF” alone. It lets you save any document as a PDF, and you will want to keep that.

Also make sure that “Let Windows manage my default printer” is switched off. Otherwise Windows keeps changing your choice.

The printer driver after a Windows update

After major updates, older printer drivers occasionally stop working. Sign: it worked for months and suddenly stopped, without you having changed anything. Then the fix is to remove the printer completely and set it up again. If, after such an update, not just the printer but the whole computer runs sluggishly, the guide “PC is slow: the most common causes” will help.

When you set it up again, you will notice that Windows is changing things in this area. This applies to Windows 11 and Windows Server 2025, not Windows 10. Since January 2026, Windows Update generally no longer delivers new manufacturer drivers. Since July 2026, Windows has preferred its own standard driver when setting up a new printer, provided the device supports the IPP printing standard; that is the case for devices with Mopria certification. For printing, that is enough. Anything more a device can do then comes through a small add-on app from the manufacturer in the Microsoft Store, the so-called Print Support App, if the manufacturer offers one. A driver already installed on your computer carries on working unaffected.

Important here: always get drivers directly from the manufacturer. The sites at the top of a search for “printer driver” are often download portals with unwanted extras.

Special cases that nobody suspects

It prints, but the page stays blank. With inkjet printers the nozzles have dried out. That happens when the device is not used for weeks. You can start a nozzle cleaning from the printer menu, and if necessary run it two or three times.

It refuses third-party cartridges. Some manufacturers block third-party cartridges via a firmware update. The device then reports a cartridge error even though the cartridge is full.

It prints from the computer but not from the phone. Then it is almost certainly the network and not the printer.

Everything only works when the computer is on. Then the printer is connected as a shared printer via another computer, instead of being on the network directly.

When repair is not worth it

With entry-level inkjet printers the sums are usually sobering. A set of original cartridges often costs more than the device, and a print head that is really finished cannot be replaced economically on many models.

If you print little and mostly text, a black-and-white laser printer is usually the more sensible purchase. Its toner does not dry out, and a toner cartridge lasts years. If it is about colour, the better route is an ink tank device rather than a colour laser. Which technology suits which need, and how to work out the cost per page yourself, is explained in the guide “Buying a printer: ink or laser?”.

What we do not do: spend hours taking apart a device that costs less to buy new than the work would. We will tell you that on the phone, before anyone sets off.

Common questions

Why does my printer say “offline” when it is switched on?

Usually its address on the network has changed or the computer has lost contact with it. First switch off only the printer and switch it on again after a minute; leave the router alone. If that makes no difference, the printer needs a fixed address in the router.

I clicked Print five times and nothing happened. What now?

Clear the queue first, then look for the cause. Otherwise all the jobs will print at once as soon as the problem is fixed.

Do I need to install the manufacturer’s driver, or is Windows enough?

For simple printing the Windows driver is often enough, and it also prints double-sided if the device has the hardware for it. For scanning and the full range of functions, however, you need the manufacturer’s software.

The printer was on the Wi-Fi and now it has gone. Why?

Often after changing the router, changing the Wi-Fi password or a firmware update. The printer then has to be connected to the network again.

Is a laser printer worth it for the home?

If you print only now and then and mostly text, yes: toner does not dry out, whereas an ink cartridge printer causes trouble after a month of standing idle. If you need colour, an ink tank printer is the better choice. They have largely solved the drying-out problem, and colour lasers are expensive.

+49 3744 4399760Mon–Fri 8:00–17:00
CallCallback

PARTS LIST · SHEET 1/1

What this page is made of

Values measured at build time. With JavaScript, your browser measures them again live.

ITEMPARTTYPESIZE
01index.htmlDocument≈ 29 kB
02styles.cssStylesheet≈ 20 kB
03scripts.jsScript≈ 13 kB
04archivo-variable.woff2Font≈ 58 kB
05ibm-plex-mono.woff2Font≈ 30 kB
06favicon.svgImage< 1 kB

Advertising or analytics cookies: none. Without your consent, the page loads nothing from third-party servers apart from Cloudflare, our delivery service. Fonts, scripts and images are hosted by us. That is how we build your IT, too.

OUTSIDE OFFICE HOURS

Feel free to call anyway

Our regular office hours are Monday to Friday, 8:00–17:00.

In the evening and at weekends the number is forwarded to us, and often someone will pick up. We cannot promise that, though.

If nobody answers, leave a short message on the voicemail: your name, your number and what it is about. We will call back as soon as we can, on the next working day at the latest.

The call costs nothing. If someone has to start work straight away outside office hours, the surcharge in the price list applies.

Call now+49 3744 4399760

Prefer to write? Use the contact form or e-mail [email protected]. We will read it on the next working day.

DIAGNOSIS · AT-K2

What do you need help with?

↵ SELECTESC CLOSECALL: +49 3744 4399760

Custom settings

Which services may load?

Strictly necessary

The choice you make here and your settings for colour scheme and motion. These are kept as small entries on your device and are never sent to a server. They are needed for the site to work and therefore cannot be switched off.