Guide · AT-R10REV. 2026-A
Wi-Fi that also reaches across the workshop floor

By Benjamin ReichertNetworks, hardware, support · IT specialist for system integration (Fachinformatiker, IHK)Last updated:
In the office it works. On the shop floor, it drops out.
The usual first attempt is a repeater from the electronics store, plugged into a socket somewhere in the middle. Afterwards it is marginally better, but still unusable. So a second repeater is added. And from then on it gets worse instead of better.
That is not the repeater's fault. It is because, as far as radio is concerned, a hall is something completely different from an office.
If you are dealing with a flat or a detached house, the scale is different and the way forward is often shorter. For that there is the guide “Improving Wi-Fi at home”.
Why repeaters fail here
A repeater receives the signal and sends it out again. Over the same radio link. That means it listens and talks in turns on the same channel.
Result: the throughput is halved. With two repeaters in a chain, a quarter is left.
Then comes the real problem. A repeater can only pass on what it still receives cleanly itself. If it stands where the signal is already weak, it spreads a weak signal, just an even weaker one.
What happens to radio in a hall
Metal reflects. Racks full of goods attenuate the signal. A high-bay warehouse with steel beams is, as far as radio is concerned, a collection of walls that do not exist on the floor plan.
And it changes constantly. A rack is rearranged, a lorry stands in the gate, a forklift parks in front of the access point. What was measured yesterday can look different today.
That is why planning from a floor plan does not work in a hall. You have to measure, and in normal operation.
The warehouse is the hardest case
Poor reception in a building means something different in every building. In the office wing it is the walls. In the warehouse it is the goods themselves.
What matters is what is on the racks. Individual cardboard boxes attenuate little, while whole pallet blocks of paper attenuate the signal considerably. Beverages absorb a particularly large amount, because water absorbs radio waves. And because stock changes, a measurement in a half-empty warehouse says little about October, when everything is full.
Then there is movement. The forklift with its terminal drives down the aisle, and the device has to switch from one access point to the next as it goes. An omnidirectional antenna under the hall ceiling mainly reaches the tops of the racks; down in the narrow aisle, little arrives. So height is not what counts here, direction is: either the devices are brought lower, towards the aisles where the forklift drives, or they hang up high and aim into the aisles with directional antennas.
Cold storage areas are best treated as a zone of their own. Insulated walls with a metal layer let hardly anything through, and an access point that is supposed to transmit into the room from outside cannot do that.
2.4 or 5 GHz? Both, but deliberately
Short and practical:
2.4 GHz carries further and passes through obstacles better, but it is slow and usually crowded. In Europe, channels 1 to 13 are permitted, and four of them can be used without overlap (1, 5, 9 and 13). Many devices nevertheless ship with the American scheme of only three channels (1, 6 and 11), which squeezes the already scarce space further. Everything the neighbouring business transmits is in the mix too.
5 GHz is much faster and has far more channels, but does not carry as far and does not like walls.
6 GHz (Wi-Fi 6E and 7) is faster still and practically empty. The range is correspondingly short, and the devices have to support it. In a hall with hand scanners from 2019, it is of no use to you.
For the hall, that generally means: 5 GHz as the working band, plus 2.4 GHz for old devices and the outer areas. Not one or the other.
However, some of the 5 GHz channels are reserved for radar. If an access point hears a radar signal on such a channel, it has to vacate it, and it may only use the new channel after a minute of listening. In halls near an airport or a weather radar, this is exactly the explanation for the phenomenon “it works, and suddenly nothing for a minute”.
What works instead
Cabled access points. Each access point gets a network cable that also supplies it with power (Power over Ethernet). That eliminates both the need for a socket and the halving of throughput. Pulling cable is the unpopular part, and it is still the most important.
Several small ones instead of one big one. There is always a wish for the one powerful device that covers the whole hall. It does not work. The access point may call out loudly, but the phone in the employee's hand still answers quietly. The connection is only ever as good as the weaker direction.
One network name for everything. All access points broadcast the same name. That is the precondition for a device to be able to roam through the hall at all, without having to sign in again manually.
When it moves on is always decided by the device itself, though. There is no handover as in a mobile phone call. The network can only make the switch attractive to the device: through coordinated transmit power, so that the next access point is clearly louder than the old one, and through a few additional standards (on the data sheet they appear as 802.11k, v and r) with which the access point tells the device where it should go. How well a device listens to this differs from model to model. When it works, that is the difference between “works” and “works while you are walking”.
And then measure. After installation, someone walks the area and checks where the signal is enough and where it is not. Only then is anything adjusted.
The point where it usually jams
Hand scanners, mobile data capture (MDE) devices and label printers.
These devices are often years old, only support 2.4 GHz and do not switch access points cleanly. They stubbornly hold on to the old connection until nothing works at all, and then sign in again. In the middle of a scan.
If devices like this are in use in your hall, they belong in the planning. Not as an afterthought, but from the start. Otherwise you end up with a technically flawless network in which the very devices it was built for are the ones that cause problems.
Two things that tend to be forgotten
Guests and production must be kept separate. The visitor at reception and the machine controller have nothing to do with each other. A separate guest network costs nothing extra if it is set up at the same time, and saves a great deal in an emergency. What matters is what is behind the second network name: a name of its own separates nothing. The separation only comes from a network segment of its own and a rule that closes the path from the guest network into the production network.
The cable behind it. Twenty access points are of little use if they all hang off one switch that is connected to the network at one hundred megabits. The bottleneck then simply moves further down the line. Whether the switch can also supply the access points with power is worked out port by port by the PoE calculator.
How we proceed
First we look at what is there. How the hall is built, what is in it, how often that changes, which devices need a wireless connection and how old they are.
Then we measure. With an access point at changing positions, in normal operation, not on a Sunday with an empty hall.
After that it is clear how many access points are needed at which points and where the cables run. And only then is anything ordered.
A first rough estimate before the appointment comes from the Wi-Fi planner: enter the hall floor area, racks and number of scanners, and it gives a range of access points. It does not replace the measurement, but you know what we are talking about.
The temptation to shorten this process is great. In our experience, shortening it ends up costing more than measuring.
In short
If the Wi-Fi in your hall keeps dropping out, the next repeater is the wrong answer. What you need is a measurement and then a handful of cabled access points in the right places.
That is more effort than a device out of the box. But it is the first time it will actually work afterwards. More on planning and setup can be found under Networks & infrastructure.
We do not quote a fixed price for this measurement, because a workshop of 200 square metres is something different from a high-bay warehouse with three aisles. You will learn what the appointment costs beforehand. And if your warehouse is sometimes full and sometimes half empty, the result also includes the reserve that you plan in for that.